Constant Voltage Dimmable LED Driver 1-10V Multi Output Current , IP20
Description:
1, Multi-output can be selectable via DIP switch. Output current: 350mA to 1050mA, output voltage:12Vdc and 24Vdc.
2, Dimmable LED driver with primary PUSH, secondary PUSH and 1-10V dimming interface.
3, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.
4, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.
5, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
6, Maximum length of the cable, from switch to last driver is 20m.
7, Factory setting: 100% dimming level and 350mA output.
8, Reset the LED diver easily by a jumper.
9, Press-in terminals in primary and secondary side, easy assembly.
10, Protection: Short circuit / Over voltage / Over temperature.
11, Long life span 50,000h, 5 years guaranty.
Applications:
For LED panel light, LED down light, led strip, led tube etc…
Dimming Operation:
A) PUSH Dim
Short push (<0.1sec): Ignore, to avoid reaction on AC spike.
Short push (0.1~1sec): Switch on or switch off.
Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.
B) 1-10V Dim
Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.
Synchronization:
For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:
A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.
B) Do a long push, the system will be resynchronized.
Specifications
|
INPUT
|
Input voltage
|
220-240Vac
|
|
Input frequency
|
50-60Hz
|
|
Input current
|
0.26A max
|
|
Power factor
|
≥0.90
|
|
Efficiency(Note1)
|
≥87%
|
|
Leakage current
|
＜0.5mA/240Vac
|
|
OUTPUT
|
Output current/voltage and load
|
350mA 16-60V DC 21W max 500mA 16-60V DC 30W max
550mA 16-60V DC 33W max 650mA 16-58V DC 41W max
700mA 16-58V DC 41W max 750mA 16-56V DC 43W max
850mA 16-56V DC 47W max 900mA 16-56V DC 50W max
1050mA 16-48V DC 50W max 12Vdc 0-1050mA 12.6W max
24Vdc 0-1050mA 25.2W max
|
|
Output load range
|
1x50W max
|
|
Current accuracy
|
±5%
|
|
Dimming mode
|
1-10V, PUSH
|
|
ENVIRONMENT
|
Working temp.(Ta)
|
-20~50℃
|
|
Surface temp.(Tc)
|
85℃max
|
|
Working humidity
|
20~90%RH non-condensing
|
|
Storage temp.
|
-40~80℃
|
|
Life time
|
≥50000hours
|
|
PROTECTION
|
Isolation class
|
Class I, SELV
|
|
Protection class
|
IP20
|
|
Short circuit
|
Protection type; auto rest
|
|
Over voltage
|
Protection type; auto rest
|
|
Over temperature
|
Protection type; auto rest
|
|
SAFETY&EMC
|
Safety
|
EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6
|
|
EMC
|
EN55015, EN61000-3-2ClassC
|
|
EN61000-3-3, EN61547
|
|
Approvals
|
SEMKO, CE
|
|
Withstand voltage
|
IN-OUT:3.75KVAC/5mA/1min; IN-FG:1500VAC/5mA/1min
|
|
OUT-FG:500VAC/5mA/1min
|
|
NOTE
|
1, Efficiency is measured at 1050mA/48Vdc output set by DIP switch
2, All parameters not specially mentioned are measured at 230Vac input, rated load and 25℃of ambient temp.
|
Your message must be between 20-3,000 characters!
