Multifunction Push 1-10V Dimmable LED Driver 30W 60Hz For LED Panel Ligt

Multifuncion dimmable led driver 1*30W output current  250-700mA 1-10V and Push 103*67*22 for led panel ligth 

 

Description:

1, ML30C-PV is multi-current and multi-voltage supply. selection of output current and voltage

through DIP switch

2, Output current and output voltage can be set by DIP switches, constant output current range from 350mA to 1050mA. Also, the LED driver supply 12Vdc / 24Vdc output voltage for you selection.

3, 12Vdc /24Vdc is not constant voltage strictly, it is a limit that the output voltage will not exceed 12Vdc /24Vdc when output 700mA. So the output road range

by 12Vdc( 0-700mA )is 8.4W max.

4. with 1-10V and push button

5, With top circuit design, AC-DC-DC, no flicker.

6, Jumper design for switching different dimming modes, it is very convenient to select suitable

dimming function as you required.

7, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the

same switch. This means there is no need for any additional synchrony wire in larger installations,

where many drivers should be controlled by one switch.

8, Memory function: The driver has built-in permanent memory against power failure. Lights can

return to previous dimming level when switch off and on again, even at mains restores.

9, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the

same switch. This means there is no need for any additional synchrony wire in larger installations,

where many drivers should be controlled by one switch.

10, Maximum length of the cable, from switch to last driver is 20m.

11, Factory setting: 100% dimming level and 250mA output.

12, Reset the LED dirver easily by a jumper.

13, Protection: Short circuit / Over voltage / Over temperature.

14.1, 5 years guaranty

 

Applications:

For led panel light, led highbay, led strip etc.

 

 

Synchronization:

 

For the resynchronization to work correctly when more than one driver is connected to the same

push button, follow steps of below after the drivers are connected:

 

A) Press push button for more than one second, followed by a short push (<1s), now, led light

switches off.

B) Do a long push, the system will be resynchronized.

 

Dimming Operation:

 

 

A) 1-10V Dim

Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.

 

B) PUSH Dim

Short push (<0.1sec): Ignore, to avoid reaction on AC spike.

Short push (0.1~1sec): Switch on or switch off.

Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.

 

 

 

 

Specifications

 

INPUT	Input voltage	220-240Vac
	Input frequency	50-60Hz
	Input current	0.16A max
	Power factor	≥0.90
	Efficiency(Note1)	≥85%
	Leakage current	＜0.5mA/240Vac
OUTPUT	Output current/voltage and load	250mA 16-60V DC 15W max  350mA 16-60V DC 21W max 400mA 16-60V DC 24W max  450mA 16-60V DC 27W max 500mA 16-58V DC 29W max  550mA 16-55V DC 30W max 600mA 16-50V DC 30W max  700mA 16-43V DC 30W max 12V DC 0-700mA 8.4W max   24V DC 0-700mA 16.8W max
	Output load range	1x30W max
	Current accuracy	±5%
	Dimming mode	1-10V, PUSH
ENVIRONMENT	Working temp.(Ta)	-20~50℃
	Surface temp.(Tc)	85℃max
	Working humidity	20~90%RH non-condensing
	Storage temp.	-40~80℃
	Life time	≥50,000hours
PROTECTION	Isolation class	Class I, SELV
	Protection class	IP20
	Short circuit	Protection type; auto rest
	Over voltage	Protection type; auto rest
	Over temperature	Protection type; auto rest
SAFETY&EMC	Safety	EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6
	EMC	EN55015, EN61000-3-2ClassC
		EN61000-3-3, EN61547
	Approvals	SEMKO, CE
	Withstand voltage	IN-OUT:3.75KVAC/5mA/1min; IN-FG:1500VAC/5mA/1min
		OUT-FG:500VAC/5mA/1min
NOTE	1, Efficiency is measured at 550mA/55Vdc output set by DIP switch  2, All parameters not specially mentioned are measured at 230Vac input, rated load and 25℃of ambient temp.

 

Mechanical Specification: